160 mhz saw filter set 10 mhz bandwidth part number: SF0160BA02329T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0160BA02329T rev b 15-mar-2010 ecn 36650 page 1 of 4 description ? 160 mhz saw bandpass filter set of two with 10 mhz bandwidth. ? 22.1 x 12.7 mm dip package, 6-14 pins. ? rohs compliant. typical performance (each filter) s11 (130-190 mhz) s22 (130-190 mhz) horizontal: frequency 6 mhz /div vertical (from top): magnitude 10 db/div magnitude 1 db/div phase deviation 5 deg/div group delay deviation 50 ns/div
160 mhz saw filter set 10 mhz bandwidth part number: SF0160BA02329T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0160BA02329T rev b 15-mar-2010 ecn 36650 page 2 of 4 specification (each filter) parameter min typ max units center frequency (fc) - 160.00 - mhz average insertion loss (155-165 mhz) - 21.3 23 db loss variation vs. temperature (25oc to 70oc ? included in above loss) - 0.7 0.75 db amplitude variation (155-165 mhz at 25oc) - 0.45 0.6 db p-p amplitude variation (155-165 mhz at 0oc,70oc) - 0.9 1.0 db p-p lower 40 db band edge 152.20 152.30 - mhz upper 40 db band edge - 167.55 167.80 mhz phase linearity (155-165 mhz) - 2.8 4 deg p-p rejection (10 to 150 mhz) 40 45 - db rejection (170 to 250 mhz) 40 48 - db input vswr - 1.8 2.0 :1 output vswr - 1.8 2.0 :1 triple transit suppression 35 42 - db system source and load impedance - 50 - ohm notes: 1. all parameters are evaluated with matching circuit. 2. this is single filter performanc e. two filters make up a cascaded pair specification (cascaded set) parameter min typ max units center frequency (fc) - 160.00 - mhz amplitude variation (155-165 mhz at 25oc) - 0.9 1.2 db p-p amplitude variation (155-165 mhz at 0o, 70oc) - 1.8 2.0 db p-p lower 80 db band edge 152.20 152.33 - mhz upper 80 db band edge - 167.45 167.80 mhz phase linearity (155-165 mhz) - 4.5 8 deg p-p rejection (10 to 150 mhz) 80 90 - db rejection (170 to 250 mhz) 80 86 - db system source and load impedance - 50 - ohm
160 mhz saw filter set 10 mhz bandwidth part number: SF0160BA02329T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0160BA02329T rev b 15-mar-2010 ecn 36650 page 3 of 4 maximum ratings parameter min max units storage temperature range -40 85 ? c operating temperature range 0 70 ? c input power level - +13 dbm matching circuit (each filter) typical component values: ls1 = 47 nh ls2 = 59.3 nh cp1 = 45 pf cp2 = 27 pf rp1 = 300 ? rp2 = 300 ? notes: 1. recommend +/-2% tolerance matching components. typical inductor q=40. 2. tuning values shown are for reference only. optimum values may change depending upon board layout input 50 ? single-ended output 50 ? single-ended gnd gnd
160 mhz saw filter set 10 mhz bandwidth part number: SF0160BA02329T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0160BA02329T rev b 15-mar-2010 ecn 36650 page 4 of 4 package outline (each filter ) marking esd/pin 1 date code square corner (denotes pin 1 location) esd/pin 1 date code square corner (denotes pin 1 location) iso 9001 registered all specifications are believed to be accurate and reliable. howe ver, spectrum microwave reserves the right to make changes wit hout notice. ? 2010 all rights reserved. units: mm tolerances are 0.15 mm except where indicated. pin configuration: input: 8 output: 14 ground: 1, 2, 7, 9 smi ba02329t xxxx filter 1 ? yyddd smi ba02329t xxxx filter 2 ? yyddd
|
